Difference between revisions of "Template:Infobox connector"
Jump to navigation
Jump to search
imported>Nasa-verve (add diameter variable to show specifications bar) |
imported>Nasa-verve (change to passband) |
||
| Line 167: | Line 167: | ||
{{!}}- | {{!}}- | ||
}} | }} | ||
| − | {{#if:{{{ | + | {{#if:{{{passband|}}}| |
| − | ! style="padding-right: 1em" {{!}} [[Passband| | + | ! style="padding-right: 1em" {{!}} [[Passband|Freq. passband]] |
| − | {{!}} colspan=2 {{!}} {{{ | + | {{!}} colspan=2 {{!}} {{{passband}}} |
{{!}}- | {{!}}- | ||
}} | }} | ||
Revision as of 07:08, 10 January 2011
| 30px | This template uses Lua: |
Template:Infobox connector is an infobox for electrical and (audio/video) signal connectors of all kinds.
The template supports three images:
- image, logo, pinout_image
Image and logo share a 300 pixel wide area - so if both are used then the width of the image should be set to 150 pixels, that is, [[Image:example.jpg|150px]]. If only image and pinout are used, then the size of both should be 300 pixels.
Usage
Template:Parameter names example
Example
| D4 Video connector | ||||
|---|---|---|---|---|
| ||||
| This example is not factual – it is purely illustrative of the infobox. | ||||
| Type | Analogue video connector | |||
| Production history | ||||
| Designer | Some guy | |||
| Designed | Early 1990s | |||
| Manufacturer | Initially Toshiba | |||
| Produced | Early 1990s to 2005 | |||
| Superseded | RF connector | |||
| Superseded by | DVI connector (2005) | |||
| Specifications | ||||
| Length | 36 mm (typical) | |||
| Width | 25 mm | |||
| Height | 6.5 mm | |||
| Hot pluggable | Yes | |||
| External | External | |||
| Electrical | 220 volts AC 50 Hz typically | |||
| Earth | Dedicate pin | |||
| Max. voltage | 450 volts peak | |||
| Max. current | 20 amps at 220 volts, 5 amps at 400 volts | |||
| Audio signal | None | |||
| Video signal | Analogue 480i, 480p, 720p, 1080i | |||
| Data signal | Resolution and Aspect ratio only | |||
| Width | 2 bits | |||
| Bandwidth | 120 bit/s | |||
| Max. devices | 1 | |||
| Protocol | Serial | |||
| Cable | 14 core shielded (25 m max) | |||
| Freq. passband | 0–20 GHz | |||
| Pins | 14 (6 video, 3 reserved, 2 detect, 3 data) | |||
| Connector | DB-25 | |||
| Pin out | ||||
| 300px A male connector seen from the front. | ||||
| Spec name | Example col title | |||
| Pin 1 | Y | luminance (0.7 V, 75 Ω) | ||
| Pin 2 | Y GND | Y ground | ||
| Pin 3 | Pb | 0.35 V, 75 Ω | ||
| Pin 4 | Pb GND | |||
| Pin 5 | Pr | 0.35 V, 75 Ω | ||
| Pin 6 | Pr GND | |||
| Pin 7 | Reserve link 1 | |||
| Pin 8 | Data line 1 | 0 V = 525 lines 2.2 V = 750 lines 5 V = 1125 lines | ||
| Pin 9 | Data line 2 | 0 V = 59.94i / 60i 5 V = 59.94p / 60p | ||
| Pin 10 | Reserve link 2 | |||
| Pin 11 | Data line 3 | 0 V = 4:3 2.2 V = 4:3 letterbox 5 V = 16:9 | ||
| Pin 12 | Plug insert detect ground | |||
| Pin 13 | Reserve link 3 | |||
| Pin 14 | Plug insert detect | output 10 kΩ, input > 100 kΩ | ||
| C1 | BLUE | Analog Blue Video | ||
| C2 | GREEN | Analog Green Video | ||
| C3 | HA_SYNC | Analog Horizontal Sync | ||
| C4 | RED | Analog Red Video | ||
| C5 | RETURN | Analog RGB Return and DDC Return | ||
| C6 | AR_PRE | Acid reflux preventer | ||
| C7 | AR_ENC | Acid reflux encourager | ||
| C8 | CHRO | Churro presence detect | ||
| These are some notes about the pinout of this connector. The pins are razor sharp. | ||||
No description.
| Parameter | Description | Type | Status | |||
|---|---|---|---|---|---|---|
| No parameters specified | ||||||
| The above documentation is transcluded from Template:Infobox connector/doc. (edit | history) Editors can experiment in this template's sandbox (edit | diff) and testcases (edit) pages. Please add categories to the /doc subpage. Subpages of this template. |
